Inspection_Maintenance (I_M) System DTC Table

Engine Controls and Fuel - 3.0L LM2 Diesel | Diagnostic Information and Procedures | Document ID: 5866920 Inspection/Maintenance (I/M) System DTC Table Description Perform the following procedure to determine if the inspection/maintenance (I/M) status monitor parameters displays Complete: Inspection/Maintenance System Check If the status monitor parameters did not update to Complete, refer to the applicable DTC listed below. Each DTC has specific conditions that must be met for the diagnostic to run. Included within the conditions are additional DTCs which, if set, may inhibit the DTCs from running. Reviewing and operating the vehicle within the conditions for running each DTC will allow the inspection/maintenance system status parameters to display Complete. Refer to: Diagnostic Trouble Code (DTC) List - Vehicle

	Scan Tool Parameter	DTCs Required to Set I/M System Status Monitor to Complete
	Boost System Monitor - Since Diagnostic Trouble Codes Cleared	P0234, P026A, P0299, P02CA, P02CB, P168A, P168B
	Catalytic Converter Monitor - Since Diagnostic Trouble Codes Cleared	P0420, P0421, P0422, P0430, P2000, P20CE, P244C
	Exhaust Aftertreatment Monitor - Since Diagnostic Trouble Codes Cleared	P2000, P20EE, P226D, P2BAA, P2BAD, P2C7A
	Exhaust Gas Recirculation Valve/Camshaft Position Monitor - Since Diagnostic Trouble Codes Cleared	P0011, P0014, P0021, P0024, P0400, P0401, P0402, P0404, P0405, P0406, P040F, P042E, P049B, P05CC, P05CD, P05CE, P05CF, P110E, P110F, P131F, P140B, P140C, P140F, P1426, P1437, P14A5, P16D0, P16D1, P241F, P2457, P2646, P2647
	Exhaust Gas Sensor Monitor - Since Diagnostic Trouble Codes Cleared	P0133, P0135, P013A, P013B, P0141, P014C, P014D, P019A, P019B, P049C, P1004, P11B3, P11CC, P11D3, P11D5, P1479, P147B, P1488, P14D9, P2209, P2297, P229F, P22A7, P22B6, P22B7, P22F9, P22FA, P22FB, P22FE, P232F, P23B5, P23B7, P23C1, P24AF, P24B4, P24B7, P24C7, P24D1, P24DA, P2627, P2628, P2A00, P2A01, P2A02, P2C62, P2C63, P2C64, P2C65
	Fuel System Monitor - Since Diagnostic Trouble Codes Cleared	P01CB, P01CC, P01CD, P01CE, P01CF, P01D0, P01D1, P01D2, P01D2, P01D3, P01D4, P01D5, P01D6, P01D7, P01D8, P01D9, P01DA, P026B, P026C, P026D, P1174, P1175, P1488, P14D9, P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3, P228C, P228D, P229A, P229B
	Oxygen Sensor Heater Monitor - Since Diagnostic Trouble Codes Cleared	P0053, P0054, P0059, P0060, P0141, P0155, P0161
	© 2023 General Mo	tors. All rights reserved.

Scan Tool Parameter	DTCs Required to Set I/M System Status Monitor to Complete
Oxygen Sensor/Heated Oxygen Sensor Monitor - Since Diagnostic Trouble Codes Cleared	P0133, P0135, P0136, P013A, P013B, P013C, P013D, P013E, P013F, P0140, P0142, P014A, P014B, P0153, P0156, P015A, P015B, P015C, P015D, P0160, P1133, P1134, P1153, P1154, P2195, P2196, P2197, P2198, P2270, P2271, P2272, P2273, P2A01, P2A02, P2A04
Particulate Filter Monitor - Since Diagnostic Trouble Codes Cleared	P144B, P144C, P144E, P144F, P2002, P226D, P226E, P2459, P24A0, P24A1